HORIZONTAL FINGER SHAPING CREATES BETTER OUTLOOK OF PRODUCT !
CKM’s new FHL-120 Horizontal Auto Finger Jointing Line is designed for horizontal finger shaping and jointing operations. Unlike the conventional vertical shaping, the FHL-120 will make the finger jointed products more beautiful outlook. It’s especially ideal for producing solid wood parquet with high production rate up to 120 pcs per minute when the production is equipped with an automatic wood arranging conveyor table.
Speed capacity 120 pcs/min
Dimensional Drawing of FHL-120
Video of FHL-120
F-C61 Wood Side Change Device
Wood Side Change Device
- After left finger shaping is performed, the side change device moves wood to the opposite side for shaping right finger.
- The device is equipped with a pressure sensor. In case wood is jammed, the machine stops automatically.
- The specially designed combination of right/left shaping and gluing operations allows for continuous feed of wood.
Powerful Suction Table
The suction table is designed to prevent wood from turning over before feeding into the pre-press assemble stand.
Ultra Uniform Wood Pressure Device
The wood pressure device at the cutting and left shaping mechanism consists of a plastic pressure plate and a cotton air hose, that ensures ultra uniform pressure for holding wood stably.
F-I31 Manual Feed Table (Optional)
Manual Feed Table (Optional)
The manual feed table allows the operator to place wood on the feed table.
F-I32 Automatic Wood Arranging Conveyor Table (Standard)
Automatic Wood Arranging Conveyor Table (Standard)
- The automatic wood arranging conveyor table provides an automatic infeed of wood, that dramatically increases productivity.
- It is constructed of a conveyor table combined with brushes for auxiliary infeed of wood.
F-T67 Chain Drive Pre-press Assembly Stand
Chain Drive Pre-press Assembly Stand
- The pre-press assemble stand employs chain feed, and provides 3 and 6 meters of length to choose from.
- This assemble stand provides pre-pressed board ready to be cut to length, and ensures accurate vertical and horizontal alignment of finger joint. The pre-press is fully synchronized with cut-to-length process.
F-A63 Assemble Press (Double Side Pressing)
Assemble Press (Double Sides Pressing)
- The assemble press employs two hydraulic cylinder at front and rear, providing more powerful and faster jointing performance. This special design also assure extremely consistent jointing effect on the entire wood.
- The assemble press joint short stock to produce long board length up to 6800 mm
- A synchronized 2-step process allows the back of the press to continue jointing and cutting to length while the front of the press is performing pressing and outfeed motions.
- Times of cut are controlled by limit switches, which permits for maximum 4 times of cut setting.
Spesifikasi FHL-120
| F-C61 Horizontal Finger Shaper | |
|---|---|
| Range of workpiece length | 150 - 700 mm |
| Range of workpiece width | 40 - 160 mm |
| Range of workpiece height | 16 - 60 mm |
| Feeding speed | 60 - 120 pieces/min. |
| Trimming saw speed | 2800 rpm (50 hz) 3400 rpm (60 hz) |
| Finger cuter speed | 5000 rpm |
| Scoring saw speed | 2800 rpm (50 hz) 3400 rpm (60 hz) |
| Power Required | |
| Feed of chain motor | 7-1/2 HP |
| Trim saw motor (and scoring saw) | 10 HP x 2 |
| Shaper cutter motor | 20 HP x 2 |
| Scoring saw motor | 1 HP x 3 |
| Cutter spindle diameter | ø 70 mm |
| Dia of Cutter (in/out) | ø 210 mm |
| Dust hood outlet diameter | 6” × 2, 4” × 4 |
| Machine dimensions (L x H x W) | 6260 × 1510 × 2550 mm |
| F-T67 Chain Drive Pre-press Assembly Stand | 6M |
|---|---|
| Range of workpiece height | 16 - 60 mm |
| Range of workpiece width | 40 - 160 mm |
| Feeding speed | 140 m/mim. |
| Feed drive motor | 2 HP x 2 |
| For conveyor motor | 2 HP |
| Brush wheel drive motor ½ | ½ HP |
| Wheel drive motor | ½ HP |
| Overall (L x W x H) | 6710 x 1140 x 1110 mm |
| F-A63 Auto Assemble Press | 6M |
|---|---|
| Available length of product | 6200 mm |
| Available thickness of product | 16 - 60 mm |
| Available width of product | 40 - 160 mm |
| Feeding speed | 80 m/min. |
| Capacity length product | 5 - 7 pcs |
| Power Required | |
| Feed drive motor | 2 HP |
| Max. assembly pressure | 0 - 150 Kg/cm² |
| Hydraulic power unit | 5 HP |
| Cut-off saw | 5 HP |
| Dust hood outlet diameter | 4” (101.6 mm) |
| Machine dimensions (L x H x W) | 7400 × 1400 × 1380 mm |
| Noise Value | 84 db |
| F-I31 Manual Feeding Table | |
|---|---|
| Conveyor table width | 700 mm |
| Feed drive motor | 1 HP |
| Machine (L x W x H) | 2500 x 950 x 910 mm |
| F-I32 Automatic Wood Arranging Conveyor Table | |
|---|---|
| Conveyor table width | 700 mm |
| Feed drive motor | 1 HP |
| Brush wheel drive motor | 1 HP |
| Machine (L x W x H) | 2510 x 1500 x 1600 mm |
Specifications, dimensions and design characteristics are subject to change without previous notice.
Pengguna lain juga melihat mesin Finger Jointing Line berikut:
FL-03-3 – Fully Auto Finger Jointing Line
FL-03-3 Fully Auto Finger Jointing Line ensures precise and efficient wood joining with strong bonds. Ideal for enhancing your production efficiency and output.
FJ-15 Advance Manual Finger Jointing System
FJ-15 Advance Manual Finger Jointing System ensures precise finger jointing, offering flexibility in manual operation and delivering strong, durable connections.
FL-10A Auto Finger Jointing Line
FL-10A Auto Finger Jointing Line offers a fully automated solution for high-precision wood jointing, supporting production efficiency & boosting structural strength.
Butuh Bantuan?
Hubungi kami untuk bantuan mengenai spare parts, service dan penawaran pisau mesin. Kami berikan solusi terbaik.
Lokasi Cabang
Temukan lokasi cabang kami yang terdekat dengan kota Anda. Kami siap membantu informasi mengenai mesin perkayuan.
Hubungi Kami
Anda butuh informasi lebih lanjut mengenai mesin kayu yang tersedia? Kami terjangkau melalui telepon dan Whatsapp.
